I need to bond two sheets of Palruf PVC roofing along one edge where they will overlap by one corrugation. Will the cement used on PVC pipe also work on Palruf? I am more interested in the strength of the bond than in it being waterproof.
If this is going to be used outdoors, the sunlight may break down the PVC cement and create some crazing in the Palruf. You may want to consider an adhesive caulk that is compatible with PVC. The PVC cement used for piping is sometimes tinted blue. The bond from this type of adhesive will be good, but the fit must be snug. The PVC Pipe cements are not meant to fill gaps. The other word of caution is ventilation. These cements are loaded with solvent which evaporates upon curing. The solvent attacks the surface of the PVC to make a bond. Again, the better choice would likely be adhesive caulk that is compatible with PVC.
Do I really need to buy Palram's recommended closure strips and screws?
In order to ensure long-term warranty coverage, it is highly recommended to use Palram-approved fasteners and accessories. Palram corrugated products, fasteners and accessories should be thought of as a system meant to provide the best possible installation. Proper use of the complete system (panels, closure strips, fasteners, etc.) greatly reduces the possibility of problems and insures that product warranty will be honored. Please see the installation instructions for the specific product for details.
Why can't I just nail the panels into place?
There are a couple of problems with nailing Palram panels. First, there is significant possibility for impact damage to the panel in the area of the attachment. Second, nailing the panels in place prevents them from safely expanding and contracting with temperature change, resulting in warping of the product. Please be sure to read the installation instructions available on each product's document page on this website.
Why do I have to predrill fastener holes?
Predrilling the holes insures the panels will have room to expand and contract properly with temperature change. Skipping this step can lead to distorted or warped panels. Please be sure to read the installation instructions located on the specific product's document page.
How do I cut these panels?
Corrugated and Multi-wall panels may be cut with a circular saw (using a very fine-toothed blade for plastic panels, veneer, or plywood). For best results, it is often better to cut a few corrugated panels at a time to reduce vibration; clamping the panels also helps. Also, if using a standard circular saw blade, better results may be seen by running the blade backwards (turn it over to reverse direction). Panels may also be cut by hand by carefully using tin snips or a utility knife. For other cutting instructions and further details, please visit each product's document page. You can also view our general Corrugated Products Installation Overview video
I'd like to use your panels to create an under-deck liner. How can I do this?
Look in the installation links
for a set of instructions on how to use our Palruf
panels for this application.
What are purlins and closure strips?
Purlins are cross members, or horizontal supporting members, running across the rafters of your structure. Suntuf, Palruf, Sun 'N Rain, and Suntop panels are fastened to purlins. Closure strips match the corrugation pattern of the panels and are attached to the purlins. Closure strips can be made of wood, foam, or plastic. Please see each product's document page for complete installation information.
Do Palram products keep the "heat" out?
Palram products are available in a variety of colors (varies by product), each with its own heat and light transmission properties. While all Palram panels block virtually 100% of harmful UV radiation, there are variations in heat and light transmission.
Clear panels allow most solar light and heat through while lighter, opaque colors are more reflective. If excessive heat buildup is a concern, our "Solar Control" panels are you're best bet. Please see each product page for more information on color offerings, light transmission percentages and warranty terms.
How long do the panels last?
Palram manufactures a variety of different products for different applications. Most have industry-leading warranties against manufacture-related defects, as well as specific warranties related to the intended use for the product. However, with proper installation and maintenance, we expect our products to far exceed the warranty periods.
Many of our products are engineered to be installed outdoors and are warranted accordingly. Nevertheless, the lifespan of outdoor products can be affected by how well they were installed, as well as environmental factors like air pollution, winds, and erosion by sand particles.
Warranty details can be found in the Downloads tab under the Warranties section at the bottom of the page for each individual product.
My building inspector says I need to know your flame spread rating. Can you provide this information?
Yes. We can provide test reports and other such documents. Please contact your Palram Dealer if you require these data, or Contact Us
. This is technical data and is not to be considered a warranty.
Do Palram accessories come in all of the same colors the panels do?
No. Palram accessories are available in some standard colors, and they may need to be specially ordered depending on your retailer.
In roofing with corrugated panels, where should I start?
You can choose to install left to right, or right to left, or start at the middle and continue to both sides. It is recommended to always advance against the dominant wind at the site. Never start at both sides, or at any two separate points.
In roofing with corrugated panels, should I insert screws at the corrugation valley or crest points?
Crest fastening is always be preferred, but some corrugated product require fastening in the corrugation valley. See the individual Installation Guide for each product to see specific instructions.
Is it OK to screw in fasteners using a power screwdriver or screw gun?
Adjustable electric screwdriver is allowed, provided you set the torque to the minimal needed, in order to prevent over-tightening and local deformation of the panel. For that reason, pneumatic tools should be avoided.
Is it OK to walk over roofing sheets while in storage, during or after installation?
No. In case it can’t be avoided during installation. It's recommended to use a crawl board that is strong enough to support the weight of the person, and that spans at least three purlins or supporting members.
How should I store packed sheets?
Store in a protected, shaded, ventilated site, with no direct exposure to sunlight and winds. In outdoor temporary storage cover with opaque protective film, and avoid PVC films and heat-absorbing materials. Please note: Surface protective films that cover sheets are highly sensitive to heat and direct sunlight. Excessive heat and direct sunlight before taking off the film can cause that film to bond the sheet surface, after which it will not be practically possible to remove it from the sheet!
Can the sheets be curved?
Yes. Sheets can be cold-curved and serve in arched shapes, provided the relevant Palram specifications for minimum radius in cold curving are followed. These specifications can be found in the Installation Instructions of the relevant sheets.
Solid sheets can be cold-curved in any direction.
Corrugated sheets can be arched so that the corrugations themselves are curved (lengthwise).
Multi-wall sheets can be arched so that the actual ribs will be curved (lengthwise).
Curving is not recommended across the ribs direction.
Can these sheets catch fire?
Yes. In principle all plastic materials are flammable, and will catch fire in presence of exterior flame. The ignition temperature of polycarbonate sheets is 490ºC (915ºF), and PVC sheets 391ºC (736ºF). Both materials are self extinguishing, and fire will decay when the exterior flame source is removed. Compared to PC and PVC, acrylic sheets are more flammable.
Do plastic roofing sheets really block UV radiation?
Some of them do. Rigid PVC and polycarbonate sheets are practically opaque to UV radiation, making them a perfect barrier against this harmful radiation. They actually block UV-A and UV-B radiation better than nearly any sunscreen lotion.
On the other hand, acrylic roofing sheets generally transmit a considerable portion of the UV radiation.
If polycarbonate sheets block UV radiation, why is there a ‘UV side’ to face outwards?
Polycarbonate (PC) inherently blocks UV radiation by absorbing it and not allowing it to pass through the panel. However, the absorption of UV also degrades polycarbonate, therefore, the sheet(s) has to be protected against UV radiation. Most Palram PC products feature a very thin co-extruded layer of UV-resistant PC resins that protect the entire sheet from UV radiation. In most cases, UV protection is applied to one side, however, two-sided UV protection is available for select products.
In order to ensure the protection of single-sides UV protected sheets, they must be installed with the marked UV protective layer facing out toward the sun. Although sheet products can also be UV protected on both sides, most of the sheets are protected on one side that is marked clearly.
Should I paint the structural rafters with any paint?
Yes, you can paint structural rafters or supports, but be sure to paint only with light or white color. Do not use dark colors like black or brown, that can absorb and reflect intensive heat.
Can I recycle my old polycarbonate or PVC panels?
Palram's Polycarbonate and PVC sheet products are recyclable. Many cities and towns have recycling programs that include curbside pick-up. If so, Polycarbonate products such as SUNTUF, SUNLITE, PALSUN, DYNAGLAS, or THERMAGLAS should be marked "Plastic #7" prior to recycling. PVC products such as PALRUF, AG-TUF, PALOPAQUE, PALCLEAR, or PALIGHT, should be marked "Plastic #3".
If local recycling is not available, other resources are available:
For PVC products, visit the Vinyl Institute's Recycling Provider Database:
For polycarbonate products, visit The Association of Post Consumer Plastic Recyclers site and download their materials buyers and seller's list:
How can I determine if a sealant is compatible with Palram's polycarbonate products?
Palram tests various sealants for compatibility with its polycarbonate product. We attempt to purchase sealants that are widely available at home improvement stores and lumber yards. Click here
to learn more about sealant compatibility and to download a list of product that have been tested.
In light of the change from "CCA" treated wood to "ACQ" treated lumber should there be a more protective screw used with the installation of Suntuf or other covering products?
The new guide lines by the manufacturers of the ACQ lumber call for heavily galvanized or stainless steel due to the corrosive nature of the ACQ treatment. The change in the treated lumber chemical is a concern. Manufacturers of ACQ do recommend the use of either stainless steel or hot dipped galvanized fasteners (which Palram’s fasteners are not made from). That said, you have two basic options for using ACQ lumber:
1. Use a comparable fastener made from an ACQ approved material. Make sure that such a fastener uses either a neoprene or EPDM washer and that it is installed per Palram’s recommendations.
2. Use Palram’s fasteners. Initial tests with ACQ have shown no adverse effect on our fasteners. This is added to the fact that the fasteners are being used to secure a light weight plastic panel (rather than connect structural members). If you use our fasteners, our 10 year warranty will still apply.
The universal plastic closure pack has 1/2 inch countersunk holes where the wood screws go, the wood vertical strips do not. Am I missing something? How are the screws going to hold the panel down if they are under the panel, Or do the screws go into the small rectangle holes?
I know it’s confusing, but they go in the rectangular holes.
Why does dripping occur on the underside of my panels?
If you have installed, or are planning to cover a patio or sunroom with Suntuf, Suntop, Palruf, Palsun, or Sunlite, it is possible that you may experience water droplets dripping from the underside of the panels, especially at the horizontal supporting members. This is almost certainly due to condensation build up on the underside of the panels. The condensation that forms is not a direct result of the Suntuf panels but rather the surrounding environment in which the panels are installed. To learn what condensation is, why it occurs, and a few suggestions that can help minimize it, download Tech Brief #5007.
Which of Palram's products have received CCMC Approval?
Several of Palram's covering and glazing products have received CCMC Approval. For details, click here.
What is the recommended ceiling height when installing Palruf or Suntuf over a barbecue or gas grill?
There really is not a set height. All grills are different and cook at various temperatures depending on what they are grilling. Customers who wish to grill under Suntuf or Palruf must be certain that the maximum temperature above the grill never exceeds 212°F for Suntuf and 122°F for Palruf. These temperatures represent the maximum service temperature for both products. If the products are subjected to temperatures higher than these, the product warranty will be voided and damage can occur to the panels.