Palram Americas
Advanced Product Search   
International / EU

Palram Americas (North American Site)
Other Regional Sites
Mexico/Cen. & So. America
Brazil (Portuguese)
Product Specific Sites (Assembly Kits)
Home    Products    Corrugated Sheets    DYNAGLAS® Family of Products    DYNAGLAS®


Corrugated Polycarbonate for Horticultural Applications


In general, polycarbonate is inherently susceptible to condensate formation, especially when used to cover totally enclosed environments like greenhouses. DYNAGLAS is made with an exclusive manufacturing process that results in the industry's first and most extensive 10-year condensate control warranty. Because effective condensate control is such a critical need for greenhouse growers, the condensate control feature is now built-in to every DYNAGLAS product.
* For corrugated polycarbonate sheets without condensate control, please visit our SUNTUF® page.


Side Lap Fastening Solutions

Palram now offers new closure solutions for DYNAGLAS. The Side Lap Profile and the Lap Clip help maintain an air-tight seal between the DYNAGLAS corrugated sheets, providing more efficient environmental control. The new closure solution is designed to prevent energy loss, damage by strong winds, and internal infiltration of dust, insects and water.

Side Lap Profile

Lap Clip

  • Fastens the panels side-laps between rafters

  • Suitable for windy climates

  • Optimized for arched and gothic structures

Main Benefits

  • Prevents energy loss

  • Prevents tearing by strong winds

  • Improves seal against dust accumulation, insects and water

Side Lap Profile

  • Specially designed for use in snowy areas, extreme wind loads (typhoons, hurricanes, monsoons)
  • Suitable for two-slope structures
  • Can be cold bent to suit arched structures at large radiuses

Main Benefits

  • Prevents energy loss
  • Prevents tearing by strong winds
  • Prevents roof cover decline under heavy snow accumulation
  • Hermetically sealed against dust accumulation, insects and water

Learn more about the Side Lap Fastening Solutions for DYNAGLAS by reading the Side Lap Fastening Solutions Sales Sheet.

International Building Code Compliance:
DYNAGLAS has been evaluated by ICC-ES (International Code Council Evaluation Service) for compliance with the 2012 International Building Code. DYNAGLAS is a light-transmitting plastic complying with IBC Section 803.1 and 2606.4 and is intended for use in interior or exterior applications.  See report ESR-1893 for complete details. For a complete list of Palram's ICC-approved products, and more details about ICC, click here.


Main Benefits
  • Available in a variety of tints and diffusion levels
  • Up to 92% PAR light transmission
  • Up to 100% diffusion
  • Highly impact resistant
  • Hundreds of sq.ft. installed over the course of nearly 30 years
  • Virtually no yellowing or loss of light transmission
  • 10-year limited warranty against loss of light due to yellowing
  • 10-year warranty for condensation control performance
  • 5-year warranty against damage due to hail
Typical Applications
  • Roofs
  • Side Walls
  • Partitions
  • Barriers
  • Doors
Other InformationPalram relies exclusively on its master distibution partner and converter, Green-Tek to manage all facets of the DYNAGLAS product line, including marketing, sales, warehousing, cutting, and logistics for full-size master-length sheets.

In turn, DYNAGLAS products are sold through commercial greenhouse distributors and greenhouse manufacturers.

Outside of North America, DYNAGLAS is sold under the brand name "Suntuf Plus."

Do I really need to buy Palram's recommended closure strips and screws?
In order to ensure long-term warranty coverage, it is highly recommended to use Palram-approved fasteners and accessories. Palram corrugated products, fasteners and accessories should be thought of as a system meant to provide the best possible installation. Proper use of the complete system (panels, closure strips, fasteners, etc.) greatly reduces the possibility of problems and insures that product warranty will be honored. Please see the installation instructions for the specific product for details.
Why can't I just nail the panels into place?
There are a couple of problems with nailing Palram panels. First, there is significant possibility for impact damage to the panel in the area of the attachment. Second, nailing the panels in place prevents them from safely expanding and contracting with temperature change, resulting in warping of the product. Please be sure to read the installation instructions available on each product's document page on this website.
Why do I have to predrill fastener holes?
Predrilling the holes insures the panels will have room to expand and contract properly with temperature change. Skipping this step can lead to distorted or warped panels. Please be sure to read the installation instructions located on the specific product's document page.
How do I cut these panels?
Corrugated and Multi-wall panels may be cut with a circular saw (using a very fine-toothed blade for plastic panels, veneer, or plywood). For best results, it is often better to cut a few corrugated panels at a time to reduce vibration; clamping the panels also helps. Also, if using a standard circular saw blade, better results may be seen by running the blade backwards (turn it over to reverse direction). Panels may also be cut by hand by carefully using tin snips or a utility knife. For other cutting instructions and further details, please visit each product's document page. You can also view our general Corrugated Products Installation Overview video.
I'd like to build a greenhouse. What are my options?
With Palram, there are several options. For hobbyist and homeowners our sister company, Palram Applications, offer easy-to-assemble greenhouse kits. Palram Applications products are available through many online resellers, and select retail garden centers throughout North America.

If you plan to design and build your own structure for your home, consider our Suntuf corrugated polycarbonate panels. Our Sunlite multi-wall panels are available in select markets as well. Suntuf is widely available at Home Depot's throughout North America, as well as many indepent retailers. Sunlite is available at select Home Depot's and some independent retailers.

For commercial applications, our DynaGlas and ThermaGlas panels are a great choice. DynaGlas and ThermaGlas are available from Commercial Greenhouse Manufacturers and Greenhouse Supply Distributors. Contact our Master Distributor, Green-Tek, for a Dealer near you.

Feel free to contact us with your specific needs and we'll help you make the best decision for your application.
Do Palram products keep the "heat" out?
Palram products are available in a variety of colors (varies by product), each with its own heat and light transmission properties. While all Palram panels block virtually 100% of harmful UV radiation, there are variations in heat and light transmission.

Clear panels allow most solar light and heat through while lighter, opaque colors are more reflective. If excessive heat buildup is a concern, our "Solar Control" panels are you're best bet. Please see each product page for more information on color offerings, light transmission percentages and warranty terms.
How long do the panels last?
Palram manufactures a variety of different products for different applications. Most have industry-leading warranties against manufacture-related defects, as well as specific warranties related to the intended use for the product. However, with proper installation and maintenance, we expect our products to far exceed the warranty periods.

Many of our products are engineered to be installed outdoors and are warranted accordingly. Nevertheless, the lifespan of outdoor products can be affected by how well they were installed, as well as environmental factors like air pollution, winds, and erosion by sand particles.

Warranty details can be found in the Downloads tab under the Warranties section at the bottom of the page for each individual product.
Is there a paint that is appropriate for polycarbonate?
Unfortunately we can’t recommend painting our panels. While polycarbonate is a very resilient material, it is potentially sensitive to chemicals contained in many exterior paints. While we can test a paint for compatibility, we have no way of controlling whether a paint manufacturer will remain consistent with their formulas over time.
My building inspector says I need to know your flame spread rating. Can you provide this information?
Yes. We can provide test reports and other such documents. Please contact your Palram Dealer if you require these data, or Contact Us. This is technical data and is not to be considered a warranty.
In roofing with corrugated panels, where should I start?
You can choose to install left to right, or right to left, or start at the middle and continue to both sides. It is recommended to always advance against the dominant wind at the site. Never start at both sides, or at any two separate points.
In roofing with corrugated panels, should I insert screws at the corrugation valley or crest points?
Crest fastening is always be preferred, but some corrugated product require fastening in the corrugation valley. See the individual Installation Guide for each product to see specific instructions.
Is it OK to screw in fasteners using a power screwdriver or screw gun?
Adjustable electric screwdriver is allowed, provided you set the torque to the minimal needed, in order to prevent over-tightening and local deformation of the panel. For that reason, pneumatic tools should be avoided.
Is it OK to walk over roofing sheets while in storage, during or after installation?
No. In case it can’t be avoided during installation. It's recommended to use a crawl board that is strong enough to support the weight of the person, and that spans at least three purlins or supporting members.
How should I store packed sheets?
Store in a protected, shaded, ventilated site, with no direct exposure to sunlight and winds. In outdoor temporary storage cover with opaque protective film, and avoid PVC films and heat-absorbing materials. Please note: Surface protective films that cover sheets are highly sensitive to heat and direct sunlight. Excessive heat and direct sunlight before taking off the film can cause that film to bond the sheet surface, after which it will not be practically possible to remove it from the sheet!
Can the sheets be curved?
Yes. Sheets can be cold-curved and serve in arched shapes, provided the relevant Palram specifications for minimum radius in cold curving are followed. These specifications can be found in the Installation Instructions of the relevant sheets.

Solid sheets can be cold-curved in any direction.

Corrugated sheets can be arched so that the corrugations themselves are curved (lengthwise).

Multi-wall sheets can be arched so that the actual ribs will be curved (lengthwise).

Curving is not recommended across the ribs direction.
Can these sheets catch fire?
Yes. In principle all plastic materials are flammable, and will catch fire in presence of exterior flame. The ignition temperature of polycarbonate sheets is 490ºC (915ºF), and PVC sheets 391ºC (736ºF). Both materials are self extinguishing, and fire will decay when the exterior flame source is removed. Compared to PC and PVC, acrylic sheets are more flammable.
Do plastic roofing sheets really block UV radiation?
Some of them do. Rigid PVC and polycarbonate sheets are practically opaque to UV radiation, making them a perfect barrier against this harmful radiation. They actually block UV-A and UV-B radiation better than nearly any sunscreen lotion.

On the other hand, acrylic roofing sheets generally transmit a considerable portion of the UV radiation.
If polycarbonate sheets block UV radiation, why is there a ‘UV side’ to face outwards?
Polycarbonate (PC) inherently blocks UV radiation by absorbing it and not allowing it to pass through the panel. However, the absorption of UV also degrades polycarbonate, therefore, the sheet(s) has to be protected against UV radiation. Most Palram PC products feature a very thin co-extruded layer of UV-resistant PC resins that protect the entire sheet from UV radiation. In most cases, UV protection is applied to one side, however, two-sided UV protection is available for select products. 

In order to ensure the protection of single-sides UV protected sheets, they must be installed with the marked UV protective layer facing out toward the sun. Although sheet products can also be UV protected on both sides, most of the sheets are protected on one side that is marked clearly.
Should I paint the structural rafters with any paint?
Yes, you can paint structural rafters or supports, but be sure to paint only with light or white color. Do not use dark colors like black or brown, that can absorb and reflect intensive heat.
What is the difference between DynaGlas® and Suntuf®?
DynaGlas™ branded products are engineered specifically for commercial greenhouse applications. Panel widths, thicknesses, pigments, and special greenhouse-specific features such as guaranteed condensate control are consistent with commercial growers' needs. Aside greenhouse-specific features, DynaGlas is the same as Suntuf (for equal thicknesses, weights, corrugation profiles, and panel widths). Outside of North America, Palram uses the Suntuf Plus brand as opposed to DynaGlas.
Can I recycle my old polycarbonate or PVC panels?
Palram's Polycarbonate and PVC sheet products are recyclable. Many cities and towns have recycling programs that include curbside pick-up. If so, Polycarbonate products such as SUNTUF, SUNLITE, PALSUN, DYNAGLAS, or THERMAGLAS should be marked "Plastic #7" prior to recycling. PVC products such as PALRUF, AG-TUF, PALOPAQUE, PALCLEAR, or PALIGHT, should be marked "Plastic #3".

If local recycling is not available, other resources are available:
For PVC products, visit the Vinyl Institute's Recycling Provider Database:
For polycarbonate products, visit The Association of Post Consumer Plastic Recyclers site and download their materials buyers and seller's list:
In light of the change from "CCA" treated wood to "ACQ" treated lumber should there be a more protective screw used with the installation of Suntuf or other covering products?
The new guide lines by the manufacturers of the ACQ lumber call for heavily galvanized or stainless steel due to the corrosive nature of the ACQ treatment. The change in the treated lumber chemical is a concern. Manufacturers of ACQ do recommend the use of either stainless steel or hot dipped galvanized fasteners (which Palram’s fasteners are not made from). That said, you have two basic options for using ACQ lumber:

1. Use a comparable fastener made from an ACQ approved material. Make sure that such a fastener uses either a neoprene or EPDM washer and that it is installed per Palram’s recommendations.

2. Use Palram’s fasteners. Initial tests with ACQ have shown no adverse effect on our fasteners. This is added to the fact that the fasteners are being used to secure a light weight plastic panel (rather than connect structural members). If you use our fasteners, our 10 year warranty will still apply.
DynaGlas Plus covered Open-Roof Greenhouse.
Photo shows a comparison between DynaGlas Plus with built-in condensate control and standard corrugated polycarbonate (center). Standard panel is covered on the inside of the panel with thousand of condensation droplets, which reflect valuable light back into the atmosphere and cause moisture-related disease.
If you're looking for maximum light transmission with excellent energy efficiency, consider instaling DynaGlas Plus together with an energy-saving automated climate screen. During the winter months, a climate control screen can be closed at night for increased heat-savings, and opened during the day for maximum light transmission and heat-gain from the sun.

During summer months, the climate control screen can be fully or partially closed to reduce heat stress on plants and heat gain within the greenhouse.
DynaGlas Plus Open-Roof Greenhouse.
DynaGlas Plus Open-Roof Greenhouse.
DynaGlas Plus used on interior partition walls.
DynaGlas Plus used on roofs, sides and ends.
DynaGlas Plus used on roofs.
Tomato growing operation.
Gothic-style, ground to ground structure covered with DynaGlas Plus.
DynaGlas Plus covered cabriolet greenhouse
DynaGlas covered cabriolet greenhouse
DynaGlas covered cabriolet greenhouse
DynaGlas covered open-roof greenhouse (Manufactured by Stuppy Greenhouse Mfg., Kansas City, MO;
 Retail garden center covered with DynaGlas Corrugated Polycarbonate.
Commercial greenhouse interior partition wall covered with DynaGlas Corrugated Polycarbonate.
Commercial greenhouse covered with DynaGlas Plus corrugated polycarbonate.